How to independently remove the tint from the glass

Tint film, glued to the glass of the car, no longer surprise. This is a common element of tuning that helps to significantly transform the “iron horse”, giving it a more serious look. But sometimes circumstances force the driver to remove the tint. In this case, knowledge will be useful.

This article describes several useful ways that will be useful not only for experienced motorists, but also for beginners. The proposed methods will help to cope with the removal of tint film.

Why the driver is forced to remove the tint

In most cases, the reason is a penalty for breaking the toning rules. It is forbidden to glue any film on the windshield, except for the upper strip. The front side windows are allowed to glue over tinted, which transmits at least 70% of the light.Rear windows are not limited, however, if they are glued mirror film, then it should be removed.

Another common cause is film aging. For a long time of operation, toning fades or various defects appear on it. Air bubbles and film detachment give the car a non-presentable look.

How to remove the tint

Tinting can quickly and accurately remove in the service station. But if it is not possible to use the services of a specialist, then you will be able to remove the film yourself. The process of rastonirovanija glasses at the beginner can take a long time. To speed up the job, ask someone to help you.

An important step in removing tinting is preparation. It is necessary to remove all linings and seals that may be damaged by tools. To remove the old tint film, there are four simple ways:

Easy tearing of the film
You will need:

• sharp knife;
• a little patience.

The main advantage of this method is the minimum set of necessary tools at hand. In the upper corner of the glass pry edge toning.Then start pulling the film towards you and down a little. Tinting should be separated from the glass diagonally. Keep it taut all the way along the length of the break and slowly pull it off. It will take a lot of time. But the tearing process can be accelerated. To do this, divide the tint into strips 15 cm wide. Use a knife carefully to avoid damaging the glass.

Using a cleaning solution
You will need:

• water;
• any detergent;
• spray gun;
• sharp knife.

Prepare the solution, it should include: one liter of water and about thirty milliliters of detergent. Pour the solution into a small spray bottle and mix well. Spray the mixture onto the upper edge of the glass and wait about one minute. During this time, the solution will penetrate between the film and glass, weakening the adhesive base. After waiting, peel off the film with a sharp knife on the edge of the glass and carefully pull it down.

Separating a small area, again sprinkle with a solution to the place of separation and wait half a minute. Then continue to separate a small portion of the film - and so on to the bottom of the glass.It is important to remember that everything needs to be done without jerking, distributing efforts evenly.

By heating

You will need:

• building or household hair dryer;
• partner.

The best tool for removing old tint film is any building dryer. You can use household, but the whole process takes much more time.

When using a building hair dryer, set the button at the minimum temperature, and set the maximum on the home appliance. Again, start at the top of the window. Heat the glass as much as possible and pull off the edge of the film. Separating a small piece, again warm up the bottom part of the toning. Thus, it will be easy to remove the entire film from the glass.

The most convenient way to do this two people. One warms the film, and the second slowly and constantly pulls it down, tearing it away from the glass. We must remember that you should not do this in the winter outdoors. In this case, the glass will crack from a sharp temperature drop.

With the help of a special solvent
You will need:

• a can of solvent;
• scraper;
• dry rags.

The stores sell a special liquid in a canister that dissolves the tint. It is applied on film and left for fifteen minutes. After the expiration of the specified time, the dissolved tinting will easily separate from the glass surface. It is also used to remove residual glue. Fluid easily penetrates under the door trim, causing metal to corrode or wiring to close. To prevent this, place a rag on top of the door trim.

Features remove tinting from the rear window

To separate the film you need to start from the side and along the threads. The pullout force should be smooth and smooth. To accelerate the separation of tinting from the glass, use a cleaning solution. After removing the tinting remains to remove residual glue from the surface of the glass.

How to remove glue residue

In most cases, to remove residues of the adhesive base, it is sufficient to use any cleaning agent and a soft scraper. If the glue on the surface of the glass was a long enough time, then it is better to remove it with acetone, gasoline or high-grade alcohol. At the same time, it is necessary to protect the trim of the doors and car seats from the ingress of these substances on them. Do not forget to use protective equipment for hands and respiratory tract.

This article has reviewed a few simple ways. All of them are proven in practice by many motorists. Choose for yourself what suits you best. Be careful while working and then you will succeed.

Video: how to remove tinted vacuum